FACE MASK MACHINE ASSEMBLE LINE DESIGN LAYOUT
Product
FACE MASK MACHINE ASSEMBLE LINE DESIGN LAYOUT
FACE MASK MACHINE ASSEMBLE LINE DESIGN LAYOUT
.Face Mask Machine
.Mask production line / Mask production machine
.Medical Surgical Face Mask Making Machine Line
Introduction
This kind of medical surgical face mask making machine is the auto equipment which be used to the product of disposable face masks, be suitable for the material of non-woven fabric , activated carbon and filter material from 1~5 layers.
This machine is fully automatic plane mask production line, Including automatic material transportation, automatic transportation, cutting off nose bridge, ultrasonic mask edge welding folding, ultrasonic fusion molding cutting、shunt transportation, ear wire cutting and welding.
Specification
Model | EPMM01 |
SIZE | 6500mm(L)☓3500mm(W)☓1900mm(H) |
Weight | <2000Kg,Ground Bearing<500Kg/m2 |
Power | Rated power 9KW |
Tact time | 60Pcs/min |
Percent of pass | 99%(Not contain Incoming materials and misoperation) |
Features
- ‧ PLC control, Servo, Automatic.
- ‧ Photoelectric detection, avoid to reduce materials waste.
- ‧ Separate model selection for children and adults.
‧ Specification of Semiautomatic Machine of KN95 / N95 Masks
‧ Simple Operation, Low Failure Rate, Enhanced Production EfficiencySlicer Equipment (part drawing)
Ultrasonic Ear Wire Equipment (part darwing)
Machine Introduction
This is a semi-automated production equipment for the production of KN95/N95 masks. It is a combination of 1pcs slicer equipment, 4 pcs semi-automatic ultrasonic ear wire cutting and welding equipment and 4pcs ultrasonic mask edge welding folding equipment. In order to complete the production of the entire product process.
The kN95/N95 mask produced by the equipment makes the three-dimensional shape suitable for the face, science of design, suitable for a variety of mouth shape, wear it comfortable, the use of multilayers of filter inlet special material design. Bacterial filtration efficiency over 95%. Masks can be produced in accordance with CN, EU and US standards.
Production Future
1. High stability, low failure rate, beautiful appearance without rust.
2. Computer PLC programming control, servo drive, high degree of automation.
3. Photoelectric detection of raw materials to avoid mistakes and reduce waste.
4. Integrated production, advanced servo speed control. One-time welding molding process.
5. The daily production capacity of KN95/N95 of one mask machine is over 45,000 PCS (20H).
6. Equipment can be designed into different shapes, can be customized design.Key Parameters
Specification
EPKN95M01
Equipment Dimension
6500(L)*2200(W)*1900mm(H)
Weight Light
<2000kg, The bearing capacity of the ground<500kg/sqm
Power Consumption
14KW
Air Pressure
0.5-0.7Mpa, 300L/Min
Environment Application
Temperature 10-35C, Humidity 35-75%, no combustible corrosive gases and other substances of more than 100,000 class.
Capacity
80Pcs/min( Min skilled worker)(Max 100Pcs/min)
Operation Worker
8-9 persons
Control Method
PLC+ Servo Drive+ Pneumatic Drive
Control Platform
Touch LCD Screen + Key Switch
Fold in Half Symmetry
+-2mm
Failure Rate
<2%
Delivery Time
15days
Percent Pass Product
99% ( not including bad incoming materials improper operation )
Equipment CombinationAn important component of mask equipment
QTY.(SET)
Notes
Water treatment layer, melt spray cloth, water absorption layer, nose tip shaping tablet
7
Inflatable shaft + clutch. (5 sets)
KN95/N95 slicer equipment
1
2 sets of servo motor control
KN95/N95 semi-automatic ultrasonic ear wire cutting and welding equipment
4-6
1 set of servo motor drive, 1 set of speed regulating motor drive
KN95/N95 ultrasonic mask edge welding folding equipment
4-6
KN95/N95 Mask Material Requirements and SpecificationsItem
Width(mm)
Coil’s outside diameter(mm)
Cartridge ‘s inside diameter(mm)
Weight(Kg)
Notes
Non-woven fabric(inner layer)
175-185
φ600
φ76.2
Max.20kg
1 layer
Non-woven fabric(outside layer)
175-185
φ600
φ76.2
Max.20kg
1 layer
Intermediate filter layer
175-185
φ600
φ76.2
Max.20kg
1 -3 layers
Nose tip shaping tablet
3-5
φ450
Φ20
Max.30kg
1 roll
Masks ear wire
5-8
–
φ15
Max.10kg
6 roll
Safety Tips for Equipment Operation- ‧ Requirements of equipment safety.
- ‧ The equipment design conforms to the principle of human-machine, convenient operation, safety, and has the overall fixed reliability design.
- ‧ The equipment must have comprehensive safety measures, especially in the equipment to turn parts, dangerous parts and all hazardous areas are equipped with protective measures, devices and safety signs. Equipment safety, ‧ ‧ environmental protection requirements to meet China’s national standards.
- ‧ Requirements for electrical safety
- ‧ The whole machine must have a power switch, gas source of the shut-off valve, to ensure that during maintenance, must close all switches, to avoid the occurrence of dangerous accidents.
- ‧ The control system platform must be placed in a position that the operator can observe and operate.
- ‧ The electrical system of the equipment must have leakage protection, overload protection and short circuit protection.
- ‧ Safety signs must be posted where equipment and electrical appliances are hazardous. Avoid accidents involving hazardous operation of personnel safety and equipment. Eliminate the occurrence of a safety accident.
.One drag two plane mask machine technical specification
Introduction
Equipment overview:
This machine is mainly used for automatic forming of flat children’s masks: after unwinding the entire roll of fabric, it is driven by a roller, and the fabric is automatically folded and wrapped; the nose beam is pulled by the whole roll, unrolled, and cut into a fixed length and then imported into the wrapped fabric. The two sides are ultrasonically welded to the seal, and then the ultrasonic lateral seal is cut and formed by the cutter; the mask is sent to the two mask ear strap welding stations through the assembly line, and the final mask is formed by ultrasonic welding; when the mask is made, Transported to the flat belt line through the assembly line to collect.Device model: JD-1490
Equipment installation and configuration requirements
1. Equipment size: 6670mm (L) × 3510mm (W) × 1800mm (H);
2. Appearance color: International standard warm gray 1C (standard color), according to this standard when no special instructions;
3. Equipment weight: ≤2000kg, ground bearing ≤500KG / m2;
4. Working power supply: rated power about 15KW;
5. Compressed air: 0.5 ~ 0.7 MPa, the flow rate is about 300L / min;
6. Operating environment: temperature 10 ~ 35 ℃, humidity 5-35% HR, no flammable, corrosive gas, no dust (cleanness not less than 100,000).
7. Operator: 1-3 people - ‧ Requirements of equipment safety.